Pressure Measurements On Two 60 Swept Delta Wings With Blunt Leading Edges And Dihedral Angles Of 0 And 45 At A Mach Number Of 495 PDF Download

Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Pressure Measurements On Two 60 Swept Delta Wings With Blunt Leading Edges And Dihedral Angles Of 0 And 45 At A Mach Number Of 495 PDF full book. Access full book title Pressure Measurements On Two 60 Swept Delta Wings With Blunt Leading Edges And Dihedral Angles Of 0 And 45 At A Mach Number Of 495.

Pressure Measurements on Two 60 Degree Swept Delta Wings with Blunt Leading Edges and Dihedral Angles of 0 Degree and 45 Degrees at a Mach Number of 4.95

Pressure Measurements on Two 60 Degree Swept Delta Wings with Blunt Leading Edges and Dihedral Angles of 0 Degree and 45 Degrees at a Mach Number of 4.95
Author: P. CALVIN. STAINBACK
Publisher:
Total Pages: 1
Release: 1962
Genre:
ISBN:

Download Pressure Measurements on Two 60 Degree Swept Delta Wings with Blunt Leading Edges and Dihedral Angles of 0 Degree and 45 Degrees at a Mach Number of 4.95 Book in PDF, ePub and Kindle

An experimental investigation was conducted to measure the pressures on two 60 degree swept delta wings with cylindrical leading edges of 0.25-inch radii and dihedral angles of 0 and 45 degrees. The tests were conducted at a Mach number of 4.95 and a stagnation temperature of 400 F. The test-section unit Reynolds number was 15.19 x 10 to the 6th power and the angle of attack was varied from 0 to 20 degrees. The results of the investigation indicated that, in general, Newtonian theory would not predict the pressure distri ution on the model in a plane normal to the leading edge for angles of attac greater than zero. A method which utilizes a linear combination of viscous and inviscid pressure terms, developed by Creager for predicting pressures on blunt-leading-e ge delta wing at angles of attac, was in good agreement with the measured pressure distributions. The stagnationline pressure level could be predicted within!9 percent by using the ideal-gas normal-shock relationship with the normal component of the free-stream Mach number. (Author).


Heat-Transfer Measurements on the Apexes of Two 60 Deg Sweptback Delta Wings (Panel Semiapex Angle of 30 Deg) Having 0 Deg and 45 Deg Dihedral at a Mach Number of 4.95

Heat-Transfer Measurements on the Apexes of Two 60 Deg Sweptback Delta Wings (Panel Semiapex Angle of 30 Deg) Having 0 Deg and 45 Deg Dihedral at a Mach Number of 4.95
Author:
Publisher:
Total Pages: 60
Release: 1961
Genre:
ISBN:

Download Heat-Transfer Measurements on the Apexes of Two 60 Deg Sweptback Delta Wings (Panel Semiapex Angle of 30 Deg) Having 0 Deg and 45 Deg Dihedral at a Mach Number of 4.95 Book in PDF, ePub and Kindle

An experimental investigation was conducted to evaluate the heat-transfer rates at the apex of two 60 degree sweptback delta wings (panel semi-apex angle of 30 degrees) having cylindrical leading edges and 0 degrees and 45 degree positive dihedral. The models tested might correspond to the first several feet of a hypersonic reentry vehicle. The tests were conducted at a Mach number of 4.95 and a stagnation temperature of 400 F. nominal test-section unit Reynolds numbers varied from 2 x 10(exp 6) to 12 x 10(exp 6) per foot. The results of the investigation indicated that the laminar heat-transfer distributions (ratio of local to stagnation-line heating rate) about the models normal to the leading edges were in close agreement with two-dimensional blunt-body theory. The three-dimensional stagnation point heat-transfer rate on the 0 degree dihedral model was in excellent agreement with theory and the stagnation-line heat transfer on the straight portion of the leading edge of both models approached a constant level 12 percent above the theoretical stagnation-line level on an isolated swept infinite cylinder. When the heating rates on the 45 degree dihedral model (planform sweep of 69.3 degree) were compared with those on the 0 degree dihedral model (planform sweep of 60 degrees) at equal angles of attack and equal lifts greater than zero, the stagnation-line heating rates on the 45 degrees dihedral model were, in general, considerably lower as a result of the difference in effective sweeps of the leading edges. On the wing panels inboard from the stagnation lines, the differences in heating were very small. The stagnation-line heat-transfer variation with angle of attack, the shift in stagnation-line location, and the reduction in stagnation-line heat transfer resulting from the increase in effective sweep when positive dihedral is incorporated into a constant-panel 0 degree dihedral wing, all agreed with the results of a theoretical study made of highly swept delta.


Pressure Distributions on a Flat-plate Delta Wing Swept 65 Deg at a Mach Number of 5.97 at Angles of Attack from 65 Deg to 115 Deg and Angles of Roll from 0 Deg to 25 Deg at a 90 Deg Angle of Attack

Pressure Distributions on a Flat-plate Delta Wing Swept 65 Deg at a Mach Number of 5.97 at Angles of Attack from 65 Deg to 115 Deg and Angles of Roll from 0 Deg to 25 Deg at a 90 Deg Angle of Attack
Author:
Publisher:
Total Pages: 32
Release: 1962
Genre:
ISBN:

Download Pressure Distributions on a Flat-plate Delta Wing Swept 65 Deg at a Mach Number of 5.97 at Angles of Attack from 65 Deg to 115 Deg and Angles of Roll from 0 Deg to 25 Deg at a 90 Deg Angle of Attack Book in PDF, ePub and Kindle


Aerodynamic Characteristics of a Delta Wing with Leading Edge Swept Back 45 Degrees, Aspect Ratio 4, and NACA 65A006 Airfoil Section

Aerodynamic Characteristics of a Delta Wing with Leading Edge Swept Back 45 Degrees, Aspect Ratio 4, and NACA 65A006 Airfoil Section
Author: William C. Sleeman
Publisher:
Total Pages: 34
Release: 1949
Genre: Aerofoils
ISBN:

Download Aerodynamic Characteristics of a Delta Wing with Leading Edge Swept Back 45 Degrees, Aspect Ratio 4, and NACA 65A006 Airfoil Section Book in PDF, ePub and Kindle

This paper presents the results of the investigation of wing-alone and wing-fuselage combination employing a delta wing having 45 degree sweepback of the leading edge, aspect ratio 4, and an NACA 65A006 airfoil section. Lift, drag, pitching moment, and root bending moment were obtained for these configurations. In addition, effective downwash angles and dynamic-pressure characteristics in the region of a probable tail location also were obtained for these configurations, and are presented for a range of tail heights at one tail length. In order to expedite publishing of these data, only a brief analysis is included.