Numerical Investigation Of Compressor Non Synchronous Vibration With Full Annulus Rotor Stator Interaction PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Numerical Investigation Of Compressor Non Synchronous Vibration With Full Annulus Rotor Stator Interaction PDF full book. Access full book title Numerical Investigation Of Compressor Non Synchronous Vibration With Full Annulus Rotor Stator Interaction.
Author | : Daniel Espinal |
Publisher | : |
Total Pages | : |
Release | : 2016 |
Genre | : |
ISBN | : |
Download Numerical Investigation of Compressor Non-Synchronous Vibration with Full Annulus Rotor-Stator Interaction Book in PDF, ePub and Kindle
The objective of this research is to investigate and confirm the periodicity of the Non-Synchronous Vibration (NSV) mechanism of a GE axial compressor with a full-annulus simulation. A second objective is to develop a high fidelity single-passage tool with time-accurate unsteady capabilities able to capture rotor-stator interactions and NSV excitation response. A high fidelity methodology for axial turbomachinery simulation is developed using the low diffusion shock-capturing Riemann solver with high order schemes, the Spalart-Allmaras turbulence closure model, the fully conservative unsteady sliding BC for rotor-stator interaction with extension to full-annulus and single-passage configurations, and the phase lag boundary conditions applied to rotor-stator interface and circumferential BC. A URANS solver is used and captures the NSV flow excitation frequency of 2439 Hz, which agrees reasonably well with the measured NSV frequency of 2600 Hz from strain gage test data. It is observed that the circumferentially traveling vortex formed in the vicinity of the rotor tip propagates at the speed of a non-engine order frequency and causes the NSV. The vortex travels along the suction surface of the blade and crosses the passage outlet near blade trailing edge. Such a vortex motion trajectory repeats in each blade passage and generates two low pressure regions due to the vortex core positions, one at the leading edge and one at the trailing edge, both are oscillating due to the vortex coming and leaving. These two low pressure regions create a pair of coupling forces that generates a torsion moment causing NSV. The full-annulus simulation shows that the circumferentially traveling vortex has fairly periodical behavior and is a full annulus structure. Also, frequencies below the NSV excitation frequency of 2439 Hz with large amplitudes in response to flow-separation related phenomena are present. This behavior is consistent with experimental measurements. For circumferentially averaged parameters like total pressure ratio, NSV is observed to have an effect, particularly at radial locations above 70% span. Therefore, to achieve similar or better total pressure ratio a design with a smaller loading of the upper blade span and a higher loading of the mid blade spans should be considered. A fully-conservative sliding interface boundary condition (BC) is implemented with phase-lag capabilities using the Direct Store method for single-passage simulations. Also Direct Store phase-lag was applied to the circumferential BCs to enforce longer disturbance wavelengths. The unsteady simulation using single-blade-passage with periodic BC for an inlet guide vane (IGV)-rotor configuration captures a 2291 Hz NSV excitation frequency and an IGV-rotor-stator configuration predicts a 2365 Hz NSV excitation frequency with a significantly higher amplitude above 90\% span. This correlates closely to the predicted NSV excitation frequency of 2439 Hz for the full-annulus configuration. The two-blade-row configuration exhibits the same vortex structures captured in the full-annulus study. The three-blade-row configuration only captures a tip vortex shedding at the leading edge, which can be attributed to the reflective nature of the BCs causing IGV-rotor-stator interactions to be augmented, becoming dominant and shifting NSV excitation response to engine order regime. Phase-lag simulations with a Nodal Diameter (ND) of 5 is enforced for the circumferential BCs for the three-blade-row configuration, and the results exactly matched the frequency response and flow structures of the periodic simulation, illustrating the small effect that phase-lag has on strongly periodic flow disturbances. A ND of 7 is enforced at the sliding interface, however the NSV excitation completely disappears and only the wake propagation from IGV-Rotor-Stator interactions are captured. Rotor blade passage exhibits a circumferentially travelling vortex similar to those observed in the full-annulus and two-blade-row simulations. This can occur when the rotating instability responsible for the NSV no longer maintains a pressure variation with a characteristic frequency signature as it rotates relative to the rotor rotation, and now has become the beginning of a spike-type stall cell. In this scenario the travelling vortex has become evidence of part-stall of the upper spans of the rotor blade, but stalling is contained maintaining stable operation. In conclusion, an efficient method of capturing NSV excitation has been proposed in a high-fidelity manner, where only 2% of the computational resources used in a full-annulus simulation are required for an accurate single-blade-passage multi-stage simulation.
Author | : Hong-Sik Im |
Publisher | : |
Total Pages | : |
Release | : 2012 |
Genre | : |
ISBN | : |
Download High Fidelity Simulation of Non-Synchronous Vibration for Aircraft Engine Fan/Compressor Book in PDF, ePub and Kindle
The objectives of this research are to develop a high fidelity simulation methodology for turbomachinery aeromechanical problems and to investigate the mechanism of non-synchronous vibration (NSV) of an aircraft engine axial compressor. A fully conservative rotor/stator sliding technique is developed to accurately capture the unsteadiness and interaction between adjacent blade rows. Phase lag boundary conditions (BC) based on the time shift (direct store) method and the Fourier series phase lag BC are implemented to take into account the effect of phase difference for a sector of annulus simulation. To resolve the nonlinear interaction between flow and vibrating blade structure, a fully coupled fluid-structure interaction (FSI) procedure that solves the structural modal equations and time accurate Navier-Stokes equations simultaneously is adopted. An advanced mesh deformation method that generates the blade tip block mesh moving with the blade displacement is developed to ensure the mesh quality. An efficient and low diffusion E-CUSP (LDE) scheme as a Riemann solver designed to minimize numerical dissipation is used with an improved hybrid RANS/LES turbulence strategy, delayed detached eddy simulation (DDES). High order accuracy (3rd and 5th order) weighted essentially non-oscillatory (WENO) schemes for inviscid flux and a conservative 2nd and 4th order viscous flux differencing are employed. Extensive validations are conducted to demonstrate high accuracy and robustness of the high fidelity FSI simulation methodology. The validated cases include: 1) DDES of NACA 0012 airfoil at high angle of attack with massive separation. The DDES accurately predicts the drag whereas the URANS model significantly over predicts the drag. 2) The AGARD Wing 445.6 flutter boundary is accurately predicted including the point at supersonic incoming flow. 3) NASA Rotor 67 validation for steady state speed line and radial profiles at peak efficiency point and near stall point. The calculated results agree excellently with the experiment. 4) NASA Stage 35 speed line and radial profiles to validate the steady state mixing plane BC for multistage computation. Excellent agreement is obtained between the computation and experiment. 5) NASA Rotor 67 full annulus and single passage FSI simulation at near peak condition to validate phase lag BC. The time shifted phase lag BC accurately predicts blade vibration responses that agrees better with the full annulus FSI simulation. The DDES methodology is used to investigate the stall inception of NASA Rotor 67. The stall process begins with spike inception and develops to full stall. The whole process is simulated with full annulus of the rotor. The fully coupled FSI is then used to simulate the stall flutter of NASA Rotor 67. The multistage simulations of a GE aircraft engine high pressure compressor (HPC) reveal for the first time that the travelling tornado vortex formed on the rotor blade tip region is the root cause for the NSV of the compressor. The rotor blades under NSV have large torsional vibration due to the tornado vortex propagation in the opposite to the rotor rotation. The tornado vortex frequency passing the suction surface of each blade in the tip region agrees with the NSV frequency. The predicted NSV frequency based on URANS model with rigid blades agrees very well with the experimental measurement with only 3.3% under-predicted. The NSV prediction using FSI with vibrating blades also obtain the same frequency as the rigid blades. This is because that the NSV is primarily caused by the flow vortex instability and the no resonance occurs. The blade structures respond passively and the small amplitudes of the blade vibration do not have significant effect on the flow. The predicted frequency using DDES with rigid blades is more deviated from the experiment and is 14.7% lower. The reason is that the DDES tends to predict the rotor stall earlier than the URANS and the NSV can be achieved only at higher mass flow rate, which generates a lower frequency. The possible reason for the DDES to predict the rotor stall early may be because DDES is more sensitive to wave reflection and a non-reflective boundary condition may be necessary. Overall, the high fidelity FSI methodology developed in this thesis for aircraft engine fan/compressor aeromechanics simulation is demonstrated to be very successful and has advanced the forefront of the state of the art. Future work to continue to improve the accuracy and efficiency is discussed at the end of the thesis.
Author | : Steven Ernest Gorrell |
Publisher | : |
Total Pages | : 260 |
Release | : 2001 |
Genre | : |
ISBN | : |
Download An Experimental and Numerical Investigation of Stator-rotor Interactions in a Transonic Compressor Book in PDF, ePub and Kindle
At close spacing the rotor bow shock is actually chopped by the stator trailing edge forming a pressure wave on the upper surface of the stator that propagates upstream until it weakens. In the reference frame relative to this pressure wave, the flow is supersonic and a moving shock wave exists that produces an entropy rise. The lower efficiency, pressure ratio, and mass flow rate measured at close spacing is a result of this extra loss. The magnitude of loss production is affected by the strength of the bow shock at the location it interacts with the trailing edge of the stator. Furthermore, the more blades present in the stator the more loss producing interactions take place. At far spacing the rotor bow shock has degenerated into a bow wave where it interacts with the stator trailing edge and is not chopped, therefore no pressure wave forms on the wake generator upper surface.
Author | : Johannes Schreiber |
Publisher | : |
Total Pages | : 214 |
Release | : 2016 |
Genre | : |
ISBN | : |
Download Investigation of Experimental and Numerical Methods, and Analysis of Stator Clocking and Instabilities in a High-speed Multistage Compressor Book in PDF, ePub and Kindle
The following experimental and numerical investigations aim at the deep understanding of the flow field in the 3.5 stages high-speed axial compressor CREATE, studied on a 2 MW test rig at the Laboratory of Fluid Mechanics and Acoustics (LMFA) in Lyon, France. This work focuses on three major objectives: Firstly, a global description of the flow field with an identification of limitations to the used exploration methods; Secondly, the characterization of the effect of stator-stator clocking in a high-speed compressor; Thirdly, the identification of instabilities arising at low mass flow rates for confirming studies on low-speed compressors and giving new insights.This work demonstrates that a mis-interpretation of steady performance data occurs easily due to measurement constraints and correction coefficients are proposed. At certain locations in the compressor, the flow field exploration (experimental and numerical) methods are identified to be challenged. This identification will initiate further development of the methods. The main mis-predictions of the simulations concern the over-prediction of the blockage induced by the tip leakage flow and eventually an over-predicted pressure rise. Furthermore, the measurements provided by the pneumatic pressure probes over-estimate the static pressure upstream of the stators. This error is induced by the interaction between the stator potential field and the probe it-self. In addition, the laser Doppler anemometry method over-estimates the velocity downstream the stators. The transport of the rotor wakes through the stators might not be correctly captured with the seeding particles in this high-speed compressor.The investigation of the stator clocking reveals only a small global effect within the measurement uncertainty band. Several contributions to the weak effect of clocking are identified by analysis of the flow structure transport, namely the time-mean mixing out of the stator wakes and the deformation of wakes along their flow path. The local effect of clocking depends on the span-height because of the variation of the circumferential position of the stator wakes and the stator blade shape over the span-height. Local possible positive and negative effects of clocking are identified and are shown to be almost in balance in this compressor. Furthermore, this work demonstrates that the unsteadiness in the flow field is not linked conclusively to the stator clocking.In this compressor, the arising instabilities depend on the operating point and flow field exploration methods. At stable operating points and nominal compressor speed, the numerical results reveal a rotating disturbance in the rotors 2 and 3, whereas the measurements show a rotating disturbance only in the first rotor and only at part speed. In both cases the disturbance exhibits rotating instability like characteristics. An exhaustive numerical study allows to exclude the commonly assumed influence of rotor-stator interactions on the rotating disturbance and pinpoints its source. New insights into the stable behavior and periodicity of the measured rotating instability are derived contrary to the unstable behavior suggested by the naming and literature. This disturbance is shown to evolve into rotating stall cells when approaching the stability limit. At nominal compressor speed, a spike type surge inception is identified I n the measured field. A precise description of the abrupt onset of the spike cell and its difference to a rotating stall cell are presented.
Author | : Jiaye Gan |
Publisher | : |
Total Pages | : |
Release | : 2016 |
Genre | : |
ISBN | : |
Download High Fidelity Aeroelasticity Simulations of Aircraft and Turbomachinery with Fully-Coupled Fluid-Structure Interaction Book in PDF, ePub and Kindle
The purpose of this research is to develop high fidelity numerical methods to investigate the complex aeroelasticity fluid-structural problems of aircraft and aircraft engine turbomachinery. Unsteady 3D compressible Navier-Stokes equations in generalized coordinates are solved to simulate the complex fluid dynamic problems in aeroelasticity. An efficient and low diffusion E-CUSP (LDE) scheme designed to minimize numerical dissipation is used as a Riemann solver to capture shock waves in transonic and supersonic flows. An improved hybrid turbulence modeling, delayed detached eddy simulation (DDES), is implemented to simulate shock induced separation and rotating stall flows. High order accuracy (3rd and 5th order) weighted essentially non-oscillatory (WENO) schemes for inviscid flux and a conservative 2nd and 4th order viscous flux differencing are employed. To resolve the nonlinear interaction between flow and vibrating blade structures, a fully coupled fluid-structure interaction (FSI) procedure that solves the structural modal equations and time accurate Navier-Stokes equations simultaneously is adopted. A rotor/stator sliding interpolation technique is developed to accurately capture the blade rows interaction at the interface with general grid distribution. Phase lag boundary conditions (BC) based on the time shift (direct store) method and the Fourier series phase lag BC are applied to consider the effect of phase difference for a sector of annulus simulation. Extensive validations are conducted to demonstrate high accuracy and robustness of the high fidelity FSI methodology. The accuracy and robustness of RANS, URANS and DDES turbulence models with high order schemes for predicting the lift and drag of the DLR-F6 configuration are verified. The DDES predicts the drag very well whereas the URANS model significantly over predicts the drag. DDES of a finned projectile base flows is conducted to further validate the high fidelity methods with vortical flow. The DDES is demonstrated to be superior to the URANS for the projectile flow prediction due to more accurate base vortex structures and pressure prediction. DDES of a 3D transonic wing flutter is validated with AGARD Wing 445.6 aeroelasticity experiment at free stream Mach number varied from subsonic to supersonic. The predicted flutter boundary at different free stream Mach number including the sonic dip achieves very good agreement with the experiment. In particular, the predicted flutter boundaries at the supersonic conditions match the experiment accurately. The mechanism of sonic dip is investigated. It is observed that the amplitude ratio of first bending mode to the second torsion mode is increased dramatically when the sonic dip occurs with a reversed trend to the flutter speed index boundary. The reduced torsional amplitude is attributed to the decreased pitching moment, which appears to be caused by the lift generation shifted toward mid-chord location. Simulation of supersonic fluid-structural interaction of a flat panel is performed by using DDES with high order shock capturing scheme. The panel vibration induced by the shock boundary layer interaction is well resolved by the high fidelity method. The dominant panel response agrees well with the experiment in terms of the mean panel displacement and frequency. The DDES methodology is used to investigate the stall inception of NASA Stage 35 compressor. The process of rotating stall is compared between the results using both URANS and DDES with full annulus. The stall process begins with spike inception and develops to full stall. The numbers of stall cell, and the size and propagating speed of the stall cells are well captured by both URANS and DDES. Two stall cells with 42% rotor rotating speed are resolved by DDES and one stall cell with 90% rotor rotating speed by URANS. It is still not conclusive which method is more accurate since there is no experimental data to compare, but the DDES does show more realistic vortical turbulence with more small scale structures. The non-synchronous vibration (NSV) of a high speed 1-1/2 stage axial compressor is investigated by using rigid blade and vibrating blade with fluid-structural interaction. An interpolation sliding boundary condition is used for the rotor-stator interaction. The URANS simulation with rigid blades shows that the leading edge(LE) circumferentially traveling vortices, roughly above 80% rotor span, travel backwards relative to the rotor rotation and cause an excitation with the frequency agreeing with the measured NSV frequency. The predicted excitation frequency of the traveling vortices in the rigid blade simulation is a non-engine order frequency of 2603 Hz, which agrees very well with the rig measured frequency of 2600 Hz. For the FSI simulation, the results show that there exist two dominant frequencies in the spectrum of the blade vibration. The lower dominant frequency is close to the first bending mode. The higher dominant frequency close to the first torsional mode agrees very well with the measured NSV frequency. To investigate whether the NSV is caused by flow excitation or by flow-structure locked-in phenomenon, the rotating speed is varied within a small RPM range, in which the rig test detected the NSV. The unsteady flows with rigid blades are simulated first at several RPMs. A dominant excitation NSV frequency caused by the circumferentially traveling tip vortices are captured. The simulation then switches to fluid structure interaction that allows the blades to vibrate freely. The simulation indicates that the structure response follows the frequency of the flow excitations that exist with the rigid blades. At least under the present simulated conditions, the NSV does not appear to be a lock-in phenomenon, which has the flow frequency locks in with the structure frequency. Overall, the high fidelity FSI methodology developed in this thesis for aircraft and engine fan/compressor aeroelasticity simulation is demonstrated to be accurate and robust. It has advanced the forefront of the state of the art.
Author | : Dana A. Gottfried |
Publisher | : |
Total Pages | : |
Release | : 2002 |
Genre | : |
ISBN | : |
Download Off-design Rotor-IGV Interactions in a Transonic Compressor - a Numerical Investigation Book in PDF, ePub and Kindle
Author | : Toshiyuki Arima |
Publisher | : |
Total Pages | : 0 |
Release | : 1997 |
Genre | : |
ISBN | : |
Download A Numerical Investigation of Transonic Axial Compressor Rotor Flow Using a Low Reynolds Number K-E Turbulence Model Book in PDF, ePub and Kindle
Presented at the International Gas Turbine & Aeroengine Congress & Exhibition, Orlando, FL, Jun 2-Jun 5, 1997.
Author | : Moosa Muhammad |
Publisher | : |
Total Pages | : 134 |
Release | : 2004 |
Genre | : |
ISBN | : 9789172838949 |
Download Numerical Investigation of Self-excited Vibrations of a Compressor Cascade Book in PDF, ePub and Kindle
Author | : D. Rayner |
Publisher | : |
Total Pages | : |
Release | : 1992 |
Genre | : |
ISBN | : |
Download A Numerical Study Into the Heat Transfer Beneath the Stator Blade of an Axial Compressor Book in PDF, ePub and Kindle
Author | : |
Publisher | : |
Total Pages | : 704 |
Release | : 1995 |
Genre | : Aeronautics |
ISBN | : |
Download Scientific and Technical Aerospace Reports Book in PDF, ePub and Kindle